top of page
waterproofing

BOSTIK DAMP PROOFER & WATER PROOFER

Bostik Damp-Proofer & Waterproofer for Floors & Roofs is a flexible, cold applied, odourless, rubber enriched bitumen emulsion for use both internally and externally. Bostik Damp-Proofer & Waterproofer for Floors & Roofs provides a highly efficient sandwich damp-proof membrane for floors. It also acts as waterproofer for walls, above ground structures and foundations.

APPLICATION AREAS

Coverage: On floors: 1.25m2/L/coat On walls: 2m2/L/coat

DOWNLOADS

Download Technical datasheet

AQUA BLOCKER LIQUID

Aqua Blocker’s MS Polymer technology combines the reliable crack bridging and waterproofing performance of a traditional, thick-layer bitumen based coating with the unbeatable ease of handling and application of a bitumen emulsion.

Aqua Blocker, as a solvent-free, water free and bitumen free waterproofer, does not require a primer coat and even adheres extremely well to damp surfaces

APPLICATION AREAS

2 COATS APPLIED:

2.3 KG/m2

 

ATTACHING SHEETS: 

0.4 KG/m2

DOWNLOADS

Download Technical datasheet

Picture1.png

BOSTIK RITO WATERSTOP LIQUID

Bostik Rito Waterstop Liquid is a versatile waterproofing liquid suitable for sealing and waterproofing roofs and walls. It contains no solvent or bitumen. No primer required and seals and protects even in the wet. Bridges cracks up to 5mm, fills voids or expansion joints to 10mm.

Bostik Rito Waterstop Liquid is a high performance waterproof coating for blocks, foundation works and a wide range of backgrounds.

APPLICATION AREAS

2 COATS APPLIED:

2.3 KG/m2

 

ATTACHING SHEETS:

0.4 KG/m2

DOWNLOADS

Download Technical datasheet

Picture1.png

K11 SLURRY GREY

Flex Slurry K11 grey is a waterproofing of building on the positive and negative side. It’s a two component sealing slurry with very high bonding strength to mineral substrates. Flex Slurry K11 is structurally sound after only a short time and with a tight seal against water under pressure.

Flex Slurry K11 is used  for sealing of cellars, underground garages, concrete elements, tunnels and shafts, etc. against ground moisture and pressurized water. It can also be used in the area of concrete renovation as a bonding slurry. 

APPLICATION AREAS

2.5-3 KG/m2

(1.5-1.8 mm Dry Layer Thickness)

DOWNLOADS

Download Technical datasheet

Picture1.png

K11 SLURRY GREY

K11 Slurry grey is a breathable, on part cement based system for waterproofing concrete and masonry. K 11 Slurry grey has a texture and consistency similar to concrete and may be brush or spray applied. It becomes an integral part of the wall and water-proofs through a crystallization process. 

K11 Slurry grey is a multiple active formulation of cements and chemical additives designed to penetrate deep in the capillaries of the substrate and form a crystalline structure. It contain no added chloride or sodium. It is inorganic, non toxic and resist chemical attack in a similar way to Portland cement. The addition of SB Bonding Agent improves better adhesion, higher flexibility and permeability resistance to K 11 Slurry grey.

APPLICATION AREAS

AGAINST MOISTURE:

1.5KG/m2 (2 COATS)

 

AGAINST NON-PRESSURIZED WATER:

2KG/m2 (2 COATS)

 

AGAINST PRESSURIZED WATER:

2.5KG/m2 (2-3 COATS)

 

COMBINED WITH BITUMINOUS CONSTRUCTION MATERIALS:

2 KG/m2 (2 COATS)

DOWNLOADS

Download Technical datasheet

Picture1.png

EVOSTIK SBR

Bostik SBR (formerly known as Cementone SBR) is a specially modified Styrene Butadiene Co-polymer Latex for cement and mortar. It toughens, waterproofs and improves chemical and abrasion resistance of renders, screeds and other cement based mixes.

 

Bostik SBR is an excellent all round primer and bonding agent especially suitable for external applications. Bostik SBR can be used for pointing, patching, bedding, waterproof rendering, tanking and flooring and for bonding renders and suction control 

DOWNLOADS

Download Technical datasheet

BOSTIK FLASHBAND

Evo-Stik Flashband Original is a self adhesive sealing bitumen strip which bonds instantly to provide a permanent watertight seal in all climates.

 

Evo-Stik Flashband Original is easily applied using hand pressure and a seam roller, with no requirement for special equipment for cutting, forming or fixing. Before using this product refer to the relevant Health & Safety Data Sheet. 

DOWNLOADS

Download Technical datasheet

BOSTIK FLASHBAND EMULSION PRIMER

Bostik Flashband Primer for Roofs is a specially designed, structured rubber bitumen emulsion for aiding adhesion of Bostik Flashband to rough or porous building surfaces.

 

Bostik Flashband Primer for Roofs may also be used for smooth porous surfaces to improve adhesion. Bostik Flashband Primer S.V. for Roofs is a solvent borne bitumen solution, for priming/sealing brickwork, cement renderings, roof tiles, concrete, mineralised felt, timber, metal, rainwater pipes, gutters and corrugated sheeting. It is also ideal to use prior to the application of other bitumen products and particularly where there are porous or dusty surfaces. 

DOWNLOADS

Download Technical datasheet

BOSTIK FUNGICIDAL WASH

Fungicidal Wash will kill moulds, lichen and algae on external surfaces such as brick, masonry, render, patios, paths, driveways and roofs. It can be used on concrete, brickwork, stone, roofing felt and most other building materials. It is not intended for use as a lawn treatment and is for outdoor use only. 

 

DOWNLOADS

Download Technical datasheet

BOSTIK EVO-BOND WATERPROOF EVO-STIK PVA

EVO-STIK Evo-Bond PVA is ready to use and is suitable for a wide range of building jobs. It is a highly effective primer, admixture, bonding agent, dust proofer and may also be used as an adhesive. EVO-STIK Evo-Bond PVA is economical, and suitable for interior use and dry service conditions. For damp or external situations EVO-STIK Waterproof Evo-Bond PVA is recommended.

1- EVO-STIK Evo-Bond PVA can be used as a PRIMER to improve adhesion to porous or difficult surfaces prior to rendering, plastering, or screeding.

2- EVO-STIK Evo-Bond PVA can be used as an ADMIXTURE to improve workability and adhesion of cement/sand mortars, renders, gypsum plasters, or screeds.

3- EVO-STIK Evo-Bond PVA can be used as a SEALER to reduce dusting of concrete and plaster surfaces.

4- EVO-STIK Evo-Bond PVA BONDS most materials, provided one of the surfaces has a degree of porosity e.g. timber, plywood, blockboard, chipboard, fibreboard, expanded polystyrene, polyurethane foam, insulating board, brick, concrete, stone, and slate.

APPLICATION AREAS

Non-porous surfaces: 23. Apply a slurry made from one part Portland Cement : one part sand mixed with one part EVO-STIK Waterproof PVA:

one part water. Stipple on with a brush and allow to dry before fixing tiles.

DOWNLOADS

Download Technical datasheet

Picture1.png

SEALOCRETE SILICONE WATERSEAL

Sealocrete Silicone Waterseal is a highly effective, clear water repellent designed to improve the resistance to rain penetration of external masonry without affecting appearance.

 

It can be applied as a damp course to repel water but will also allow water vapour through, allowing a wall to breathe. Sealocrete Silicone Waterseal protects against frost damage, efflorescence, mould, fungal growth and surface contamination by dirt. It is suitable for external use on brickwork, cement renderings, concrete blocks and certain types of natural and artificial stonework.

APPLICATION AREAS

Dependent on the porosity of the area to be treated, approx. 6m2 per litre on hard brickwork and approx. 4m2 per litre on porous surfaces. Some very porous stone may take several coats. For injection the usage is approx. 1 litre per 0.7 –

1.0m of 100 – 120mm brickwork.

Untitled.png

PAVESEAL

Bostik Pave Seal (formerly known as Cementone Pave Seal) is a clear, low viscosity, solvent based acrylic solution that penetrates deeply into dry concrete, brick, porous tiles etc.

 

Bostik Pave Seal provides excellent resistance to water and dirt. It also enhances the colour of the treated surface. 

APPLICATION AREAS

Approximately 5 – 8m2 per litre per coat depending on porosity of surface.

DOWNLOADS

Download Technical datasheet

Untitled.png

SEALOCRETE SEALOROOF

Sealocrete Sealoroof is a flexible fibre reinforced roof coating for instant weatherproofing on most conventional roof substrates. It has been designed for the long term maintenance of industrial and domestic roofs. It can be applied to dry or damp substrates to provide an effective and economical solution for the remedial repair of leaking roofs. It has excellent crack bridging properties and cures to produce a water impermeable coating with excellent adhesion to most building materials and conventional roofing substrates such as old roofing felt, asphalt, bituminous roof coatings cement and brickwork. If using on a roof or balcony subject to heavy foot traffic, regular use or the placing of objects such as garden furniture then promenade tiles or a similar protective material must be used.

APPLICATION AREAS

On Sloping Roof:

ONE Coat:

1KG/m2

 

On Sloping Roof which Ponds:

TWO Coats 1KG/m2

DOWNLOADS

Download Technical datasheet

Picture1.png

BOSTIK BRICK & PATIO CLEANER

Cementone Brick & Patio Cleaner is an effective and economical way to remove stains and limescale from brickwork, concrete, paving, tiles, etc. It also cleans away dirt, grime and algae. 

APPLICATION AREAS

3-5 m2/L

1 Part: 3 Parts Water

DOWNLOADS

Download Technical datasheet

Picture1.png

BOSTIK EVO-BOND EVO-STIK PVA

Bostik Rapid Hardener & Plugger is based on calcium chloride and surface active materials. It is formulated to accelerate the setting of cementitious mixes and to aid the attainment of high early strength in concrete and mortar mixes. It is suitable for use with cement and concrete mixes, precast concrete, dense heavy duty renderings and plugging pressure leaks. 

APPLICATION AREAS

UNDILUTED:

14 m2/L

DOWNLOADS

Download Technical datasheet

Picture1.png
bottom of page